Resource LibraryUser GuidesH1010 · H1012

H1010 · H1012

Heckler Confidence Stand

Assemble the Confidence Stand, mount the display, organize cables, and prepare the stand for storage.

This guide is also available as a printable PDF.

Important: Read Before Assembly

Thank you for choosing the Heckler Confidence Stand. To ensure safe and proper assembly, operation, and maintenance of this product, it is essential to thoroughly read and understand this user guide before beginning any assembly.

Failure to follow the instructions and safety guidelines provided in this manual may result in serious personal injury, equipment damage, or voided warranties.

Assembly Requirements: This product requires multiple people to assemble and safely mount the display. Attempting to assemble or mount the display alone could result in injury or damage to the equipment.
Weight and Stability: Ensure that the stand is placed on a stable, level surface during assembly and when in use. Uneven or unstable surfaces may cause the stand to tip over, leading to potential injury or damage.
Use Proper Tools: Only use the recommended tools for assembly. Improper tools or techniques may damage the components and compromise the safety and stability of the stand.
Display Mounting: Mounting a display on this stand requires careful attention to weight limits and proper alignment. Exceeding weight limits or incorrect mounting can cause the display to fall, resulting in injury or damage.
Secure All Components: Ensure all bolts, screws, and other fasteners are securely tightened and engaged as per the instructions. Loose or improperly engaged components may cause the stand or display to become unstable.
Electrical Safety: If your display or any attached components require electrical connections, ensure that all wiring is correctly installed and free of damage. Avoid routing cables where they could be pinched or damaged during assembly or operation.
Routine Inspection: Regularly inspect the stand and mounted display for any signs of wear, damage, or loose components. Address any issues immediately to maintain safety and functionality.

Heckler Design is not liable for any injuries, damages, or losses resulting from improper assembly, use, or maintenance of this product. By assembling and using this product, you agree to follow all safety guidelines and instructions provided in this user guide.

In the box

1 x Beam (R1010)
2 x Display Rail (R1020)
2 x Packout Ring (P134)
4 x Leg (R1014)
2 x Clamp Bracket (R1060)
2 x Knob Screw (P131+F206)
4 x Caster (F190)
4 x M8 thumbnut (P132+F207)
4 x M8 setscrew (F209)
4 x M6 thumbnut (P133+F208)
4 x M6 setscrew (F210)
1 x Velcro strap (F856)

Stand components and mounting hardware labeled a through l, including the packed beam, display rails, legs, casters, clamp brackets, knobs, nuts, screws, and strap.

Unpack the box

Packed stand with straps released and reusable packout rings holding the rails and legs around the beam.

Install casters

Engage the caster brake.

Insert the caster's post into the leg socket.

Caster post aligned below a leg socket, with the brake pedal pressed downward.

Rotate the caster until the hex shapes are aligned.

Push until you feel the grip ring pop into position. The hex feature should be fully seated inside the leg socket.

Caster rotating to align its hex feature with the leg socket, then seated fully inside the leg.

Install legs

Lay the beam on the ground and install the first leg.

First leg aligned with the beam socket, with its side screw directed toward the alignment notch.

Once the leg has entered its socket, fully depress both spring buttons.

Two spring buttons on a partially inserted leg being pressed inward.

Continue inserting the leg until the two tabs on its top pass through the slots in the beam's surface.

Two tabs on the leg projecting through slots in the beam surface.

Verify that both spring buttons fully protrude through the holes on the beam.

Leg fully inserted with its spring buttons projecting through the beam holes.

Side close-up of both spring-button heads protruding through opposite beam surfaces, each circled.

Beam with the first leg and caster installed.

Repeat this process for the rear leg while keeping the beam and first leg resting on the ground or tabletop.

Second leg entering the rear socket while the beam and first leg rest on the surface.

Repeat the process with the remaining two legs.

Upright the completed stand base.

Completed upright base with four legs and casters.

Install display rails

Install the included set screws onto the display.

Four set screws installed in the rear display mounting holes, with one screw enlarged.

Determine the optimal position for mounting the display rails on your display.

Two display rails on the rear of a display, with their lower ends no more than 11 inches above the display’s bottom edge.

Place the display rails on the display.

Fully fasten all four thumbnuts.

Three views of the display rails lowering over the set screws and being secured with four thumb nuts.

Install display to beam

Confirm all casters are locked.

Identify the display's horizontal VESA pattern and find the matching mounting slots on the beam.

Beam mounting slots highlighted with downward arrows.

Beam slot positions for a 200 mm horizontal VESA pattern.

Beam slot positions for a 300 mm horizontal VESA pattern.

Beam slot positions for a 400 mm horizontal VESA pattern.

Beam slot positions for a 500 mm horizontal VESA pattern.

Beam slot positions for a 600 mm horizontal VESA pattern.

Align the tooth-shaped tab of the display rails to the mounting slots on the beam.

Bring the display closer to the beam and fully insert the tooth-shaped tabs into both slots.

Allow the display to rest on the beam.

Display rails approaching the beam and engaging their tooth-shaped tabs in its slots.

Four close-ups showing a rail tab aligning with a beam slot, inserting through it, and lowering into engagement.

Install both clamp brackets and fasten both knob screws as illustrated.

Leave the knobs loose at this step.

Two clamp brackets positioned around the beam behind the display rails, with their knob screws shown.

Adjust the display angle by rotating it along the center beam to your desired position.

Side view of the display tilting around the beam to different angles.

Fully tighten the knob screws to secure the display at your preferred angle.

Two knob screws securing the display-rail clamps, with one knob enlarged.

Organize cables

Cable routed along a display rail and secured with straps for strain relief.

Packout and storage

Attach both storage rings on the display rail as shown.

Two reusable packout rings fitted to a display rail.

Place the second display rail as shown.

Second display rail nested alongside the first in the packout rings.

Place four legs as shown.

Four legs nested together between the display rails in the packout rings.

Place the beam as shown.

Beam positioned alongside the packed legs and rails in the rings.

Install the Velcro straps with steel buckles.

Two straps threaded around the packed stand components.

Straps tightened around the packed components through their buckles.

Close-up of a strap passing through its buckle and securing the components in a packout ring.

Questions?

Email us at service@heckler.com

Call us at (844) 432-5930

Chat with us at heckler.com