Enlarge image ↗ Shelf top and tray body with cable managers, screw collars, thumb screws, and mounting anchors labeled A through F.
1 x Shelf top (R1021) 1 x Main Body (R1022) 4 x Cable Managers (P118) 2 x Thumb Screw Collars (P138) 2 x M8 Thumb Screws (P137, F003) 2 x Mounting anchor assemblies (P136-2, F212, F218) Pull the shelf-stopper from the underside of the shelf top. Removing the stopper enables the shelf top to be removed from the main body.
Enlarge image ↗ Close-up of the shelf stopper beneath the shelf top, with an arrow showing it being pulled downward.
Slide the shelf top laterally, in the direction away from the shelf-stopper.
The shelf top is mounted to the main body with six grippy urethane standoffs. You may need to bump the end of the shelf top to initiate removal.
Lift the shelf top from the main body.
Enlarge image ↗ Shelf top sliding sideways, then lifting away from the tray, shown with numbered arrows.
Note which mounting slots on the rear surface of the tray correspond to the columns on your Heckler rolling stand.
Enlarge image ↗ Rear tray mounting slots labeled at 50 mm intervals, with mounting widths from 200 to 1000 mm marked.
Snap the two mounting anchors into the desired mounting slots.
Enlarge image ↗ Two mounting anchors aligned with selected slots on the rear of the tray.
Ensure each extrusion is fully inserted into the mounting slot.
From the inside of the tray, insert the thumb screw collar and thumbscrew as illustrated.
Hand-tighten the thumbscrews.
Enlarge image ↗ Screw collar and thumb screw inserting through the tray into a mounting anchor; the final view shows the screw seated.
Select your desired mounting height for the hub.
You may find it more convenient to first install your display to the rolling stand. Then calculate the clearance required between the display and shelf for the equipment you intend to place atop the shelf.
Enlarge image ↗ Tray positioned beneath a display on the rolling stand, with the mounting location and equipment clearance indicated.
Lower the tray’s mounting anchors onto both columns.
Enlarge image ↗ Tray mounting anchor aligned with two openings in a stand column.
Enlarge image ↗ Tray lowering so its anchor engages the column openings.
Enlarge image ↗ Mounted tray anchor seated in the column, marked with a check.
Enlarge image ↗ Tray attached across both stand columns.
Insert four cable managers into the back of the mounting anchors to lock the tray to the columns.
When properly inserted, the cable managers should be fully seated against the rear surface of the columns.
Failure to install the cable managers could allow the hub to inadvertently dislodge from the columns, which could cause equipment damage.
Enlarge image ↗ Four cable managers inserting into the rear of the column mounting anchors, shown in close-up before and after seating.
Mounting a Logitech Rally Bar, Rally Bar Mini, or Rally Bar Huddle above the shelf top using H1042 Rally Bar Mount for Heckler Mobile Fleet enables you to access your tray contents without removing your video bar.
If using H1042 Rally Bar Mount for Heckler Mobile Fleet (sold separately), fasten the mount to the tray as illustrated.
Enlarge image ↗ Optional H1042 camera mount aligned with the tray slots and secured with two fasteners.
If you have not already done so, install your display to the columns of the rolling stand. Follow the procedures and safety instructions detailed in the user guide for your rolling stand.
Enlarge image ↗ Rear view of a display aligned with the rolling stand columns above the tray.
Place power strips, power adapters, and other small devices into the tray.
Bundle extra cabling and place inside the tray.
Enlarge image ↗ Power strip, power adapter, and bundled cables placed inside the tray.
Extend the cables for your video bar, touch controller, and display over the outer edges of the tray.
Connect cables to your display(s). Route cables from the display through the cable managers then store extra cabling in the tray.
Enlarge image ↗ Display cables routed down the columns through cable managers, into the tray, and along the lower beam.
The shelf top's surface features slots for attaching video bars, PTZ cameras, and other cameras directly using standard 1/4-20 screws (not included). Be sure to secure your camera to the shelf top before attaching the shelf top to the tray.
Fasten your camera to the shelf top using 1/4-20 hardware (not included) that works well with your PTZ camera or video bar.
Enlarge image ↗ Camera mounted to the shelf top through its slotted mounting plate.
Lower shelf top onto the tray.
Enlarge image ↗ Shelf top and camera lowering onto the tray, with downward arrows at both ends.
Slide the shelf top toward the right side of the tray (when facing the front) until the anchors reach the ends of the keyholes.
Enlarge image ↗ Shelf top sliding to the right across the tray to engage its mounting anchors.
Push the shelf-stopper onto the threaded post on the underside of the shelf top.
Enlarge image ↗ Shelf stopper seated on the threaded post beneath the shelf top.
Enlarge image ↗ Shelf top secured on the tray beneath the display, marked with a check.
Enlarge image ↗ Camera and touch controller placed on the shelf top beneath the display.
Enlarge image ↗ Rear view of power and data cables connected to the camera and touch controller on the shelf.
Enlarge image ↗ Close-up of the device cables tucked over the edge and into the tray.
