Important: Read Before Assembly
Thank you for choosing Heckler Stand for Neat Board Pro. To ensure safe and proper assembly, operation, and maintenance of this product, it is essential to thoroughly read and understand this user guide before beginning any assembly.
Failure to follow the instructions and safety guidelines provided in this manual may result in serious personal injury, equipment damage, or voided warranties.
Assembly Requirements: This product requires multiple people to safely mount the display. Attempting to mount the display alone could result in injury or damage to the equipment.Weight and Stability: Ensure that the stand is placed on a stable, level surface during assembly and when in use. Uneven or unstable surfaces may cause the stand to tip over, leading to potential injury or damage.Use Proper Tools: Only use the recommended tools for assembly. Improper tools or techniques may damage the components and compromise the safety and stability of the stand.Display Mounting: This stand is compatible only with the Neat Board Pro. Attempting to mount other devices and displays can cause instability resulting in injury or damage.Secure All Components: Ensure all bolts, screws, and other fasteners are securely tightened and engaged as per the instructions. Loose or improperly engaged components may cause the stand or display to become unstable.Electrical Safety: If your display or any attached components require electrical connections, ensure that all wiring is correctly installed and free of damage. Avoid routing cables where they could be pinched or damaged during assembly or operation.Routine Inspection: Regularly inspect the stand and mounted display for any signs of wear, damage, or loose components. Address any issues immediately to maintain safety and functionality.Heckler Design is not liable for any injuries, damages, or losses resulting from improper assembly, use, or maintenance of this product. By assembling and using this product, you agree to follow all safety guidelines and instructions provided in this user guide.
1 x Beam (R1081) 4 x Leg (R1082) 2 x Column (R1080) 4 x Caster (F189) 2 x Column cap (P274) 2 x Cable manager (P284) 2 x Column cap mounting screw (F308) 1 x Assembly hex key (F674) 1 x Velcro strap (F856) Enlarge image ↗ Beam, four legs, and two columns labeled a–c.
Enlarge image ↗ Casters, column caps, cable managers, cap screws, hex key, and strap labeled d–i.
Engage the caster brake.
The casters have a total lock feature, locking the wheels from spinning as well as the swivel axis from swiveling.
Enlarge image ↗ Caster brake pedal pressed downward to engage its lock.
Thread the caster into the leg socket.
Enlarge image ↗ Caster threaded stem aligned with the socket in the end of a leg.
Thread the caster all the way into the leg insert. The hex feature of the caster should be fully seated inside the leg socket.
Enlarge image ↗ Close-up of the caster’s threaded stem turning into the leg socket.
Enlarge image ↗ Caster fully seated with its hex feature inside the leg socket.
If the leg becomes misaligned during your installation attempt, remove the leg from the socket and try again. Attempting to pry or force a misaligned leg into position may cause damage to the stand.
Lay the beam on the ground and install the first leg. Use the supplied hex key to back out each set screw to enable the leg to slide into the socket without striking the tip of the set screws. Do not fully back out the set screws. They should still stay engaged with the beam.
Each leg socket ships with two set screws pre-installed. Check to ensure two set screws are present at each leg socket location. If any set screws are missing, check your packaging and contact Heckler customer service for replacement parts.
Enlarge image ↗ Hex key backing out the two set screws beside a leg socket.
Orient the leg so that the surface with the two holes aligns with the two set screws, and insert the leg into the socket.
Enlarge image ↗ Leg aligned with the beam socket so its two holes face the set screws.
Depress the silver safety push pin on the side of the leg, then push the leg fully into the socket.
Enlarge image ↗ Leg pushed into the socket while its side safety pin is depressed.
When correctly inserted the safety push pin will click inside of the round beam tube and the two tabs on the end of the leg will be flush with the outside surface of the beam.
Enlarge image ↗ Close-up of the safety pin inside the beam with the leg seated.
Enlarge image ↗ Leg-end tabs visible flush with the beam’s outer surface.
Tighten the two set screws.
Tighten the screws firmly, but do not overtighten. The set screws should rest near-flush to the beam surface. The set screws should not sink into the beam beyond flush.
As the set screws fasten into place, the conical tip of the set screws will align with the conical holes in the leg. You’ll feel the leg align into its final position.
Enlarge image ↗ Hex key tightening the leg socket’s set screws.
Enlarge image ↗ First leg and caster installed on the beam.
Repeat the process with the remaining three legs.
Enlarge image ↗ Remaining three legs attached to the beam with the base inverted.
Set the completed stand base upright.
Enlarge image ↗ Completed four-caster base standing upright.
Engage the brake on all four casters.
Enlarge image ↗ Caster brake pedal shown in its locked position.
Identify the two column sockets on the beam. Use the supplied hex key to back out each set screw to enable the column to slide into the socket without striking the tip of the set screws.
Each column socket ships with two set screws pre-installed. Check to ensure two set screws are present at each column socket location. If any set screws are missing, check your packaging and contact Heckler customer service for replacement parts.
Enlarge image ↗ Hex key backing out the two set screws at a column socket.
Align the end of the column with the socket on the beam and insert it.
Hold the column vertically throughout this process to ensure proper socket alignment. If the column becomes misaligned during your installation attempt, remove the column from the socket and try again. Attempting to pry or force a misaligned column into position may cause damage to the stand.
Enlarge image ↗ Side view of a column aligned vertically above the beam socket.
Enlarge image ↗ Front view of the column aligned above its socket on the assembled base.
Enlarge image ↗ Column end positioned above the beam socket with its holes facing the set screws.
Depress the silver safety push pin on the side of the column, then push the column fully into the socket.
Enlarge image ↗ Column pushed into the socket while its side safety pin is depressed.
When correctly inserted the safety push pin will click inside of the round beam tube and the two tabs on the end of the column will be flush with the outside surface of the beam.
Enlarge image ↗ Cutaway showing the column’s safety pin inside the beam.
Enlarge image ↗ Column-end tabs visible flush with the beam’s outer surface.
Tighten the two set screws.
Tighten the screws firmly, but do not overtighten. The set screws should rest near-flush to the beam surface. The set screws should not sink into the beam beyond flush.
As the set screws fasten into place, the conical tip of the set screws will align with the conical holes in the column. You’ll feel the column align into its final position.
Enlarge image ↗ Hex key tightening the column socket’s set screws.
Repeat this process to install the second column.
Enlarge image ↗ Second column installed on the completed base.
Engage the lock on all four casters.
Enlarge image ↗ Both columns installed with a close-up reminding the installer to engage the caster brakes.
Bring the Neat Board Pro close to the columns. Align the upper two mounting anchors on the Neat Board Pro with the top slots on the columns. Align the lower two mounting anchors with the lower cutouts on the columns. Lower the Neat Board Pro into place on the columns.
Enlarge image ↗ Neat Board Pro’s rear mounting anchors aligned with the two stand columns.
Enlarge image ↗ Close-ups of the upper and lower display anchors lowered into the column openings.
Install the column caps.
Enlarge image ↗ Column cap pressed into the top of a column.
Install the cable managers.
Enlarge image ↗ Cable manager inserted into the rear column slot and slid down into place.
Install the screws in the cap.
Enlarge image ↗ Hex key driving the column-cap mounting screw through the cap.
Route cables along the columns.
Enlarge image ↗ Cables routed down the column through the cable managers.
Organize the cable along the rear leg with the provided Velcro strap if needed.
Enlarge image ↗ Cables secured along a rear leg with the provided strap.
Before loosening any frame set screws, remove the Neat Board Pro from the stand with at least two people and place it securely, following the manufacturer’s handling guidance. Do not disassemble the frame while the display is mounted. Once the stand is unloaded, back out the set screws to disassemble the columns and legs from the beam.
Enlarge image ↗ Hex key backing out the beam set screws for disassembly.
Push the included hex key through the hexagonal cutout on the leg or column to release its safety pin, then pull the leg or column out of the beam.
Enlarge image ↗ Hex key inserted through the release opening to depress the safety pin while the leg is withdrawn.
Enlarge image ↗ Leg fully withdrawn from the beam socket.
