1 x Base (R1040) 1 x Column (R1039) 1 x Device Panel (R1038) 1 x Felt panel (F322 series, in the ordered color) 2 x Cable trim (P218) 3 x M8 thumbscrew (P217 + F270) 1 x M10 thumbscrew (P221 + F267) 4 x M8 set screw (F029) 4 x M6 set screw (F269) 4 x M8 thumbnut (P231) 4 x M6 thumbnut (P232) 4 x Display spacer (P215) 4 x M4 thumbnut (F838) 4 x M4 thumbscrew (F839) 1 x Velcro (F856) Enlarge image ↗ Base, column, device panel, and felt cover labeled a through d.
Enlarge image ↗ Cable trim, M8 and M10 thumbscrews, display hardware, M4 fasteners, and strap labeled e through o.
Align two tabs on the bottom of the column with the slots on the base. Use the M10 thumbscrew provided to fully fasten the column to the base.
Enlarge image ↗ Column aligned above the base with a thumbscrew below.
Enlarge image ↗ Close-up of the column tabs aligned with base slots and the fastening screw underneath.
Enlarge image ↗ Column fastened upright on the base.
Install the cable trims to the storage box as shown.
Enlarge image ↗ Two cable trims aligned with the device-panel openings.
Enlarge image ↗ Cable trim approaching its opening, shown in close-up.
Enlarge image ↗ Cable trim seated around the opening.
Use three M8 thumbscrews provided to install the storage box to the column as shown.
To prevent scratching the top surface of the base during this step, place the felt cover over the front two-thirds of the base.
Enlarge image ↗ Device panel aligned with the column and three M8 thumbscrews.
Enlarge image ↗ Device panel fastened to the column with three thumbscrews.
This stand is designed to safely mount displays with screen sizes of 55-inch or smaller, with VESA 200 and VESA 300 horizontal mounting patterns. VESA 400 mounting patterns are intentionally not supported.
Determine if your display has M6 or M8 size mounting holes.
Fasten the supplied display-mounting screws into the four VESA mounting positions on your display.
In most cases, no tools are needed for this step. Fasten by hand. If you use a tool (not included) to fasten the set screws, do not overtighten.
Enlarge image ↗ Four set screws installed behind the display, with one enlarged.
Slide the display spacers down over the set screws.
Enlarge image ↗ Four display spacers sliding onto the set screws.
Choose the mounting position on the Device Panel based on the preferred display mounting height. Fasten the corresponding M6/M8 thumbnuts from the inside of the Device Panel.
To prevent damage to your display, once set screws are resting on the Device Panel, hold the display to the device panel with one hand while fastening the thumb nuts with your other hand.
Enlarge image ↗ Four thumbnuts aligned with the set screws through the device panel.
Enlarge image ↗ Display secured to the device panel.
Use the M4 thumbscrews and thumbnuts to install the wall mount of the video conference equipment (not included) as shown.
Enlarge image ↗ Video-bar wall mount aligned with four M4 thumbscrews and thumbnuts.
Enlarge image ↗ Video-bar wall mount fastened beneath the display.
Install the video bar to its wall mount.
Enlarge image ↗ Video bar installed beneath the display.
Use the Velcro strap included to fasten and organize devices and cables to the grid pattern on the Device Panel.
To reduce the installation height of some adapters, use the inline C7 (figure eight) adapter provided by Logitech with the power adapter for Tap PoE injector and the power supply for MeetUp 2.
Purchase and mount the compact four-outlet power strip (sold separately) to provide power to the display, video bar, touch controller, and mini PC while using a minimal amount of storage space.
Route the power cable up from under the base, through the large grommet on the bottom of the base.
Enlarge image ↗ Devices and cables organized on the rear grid with routing through the lower opening.
In areas of seismic activity, you can bolt the stand to the tabletop utilizing the two small grommeted holes in the base. Use 1/4-20 threaded bolts, nuts, and washers through your tabletop. Hardware not provided.
Enlarge image ↗ Felt cover approaching the rear storage area.
Enlarge image ↗ Felt cover seated over the device panel.
Enlarge image ↗ Completed tabletop stand with display and video bar.
