Welcome to the new Heckler website. Need help or want to share feedback? Use chat or the Feedback tab.

Heckler
Skip to guide content
Resource LibraryUser GuidesH597

In this guide

H597

Heckler VESA Mount for Video Bars

Check the display mounting pattern, install the VESA bracket, and mount and cable the video bar.
H597 VESA video-bar mount supporting a fitted video bar beneath a display.

This guide is also available as a printable PDF.

Letter PDFA4 PDF

In the box

  1. 1 x VESA Mount (R1085)
  2. 1 x Video Bar Mount (R1086)
  3. 2 x Spacers for upper VESA positions (P295)
  4. 4 x Thumbscrews (F839)
  5. 4 x Thumbnuts (F838)
Labeled parts: perforated VESA plate, slotted Video Bar Mount, two upper spacers, four loose thumbscrews, and four thumbnuts.

Installation

Determine display compatibility

Measure the bottom hole of the VESA Mount to the bottom edge of the display. Confirm this distance is 11.2 inches (284 mm) or less.

Rear of a display with a dimension from the lower VESA hole to its bottom edge labeled 284 mm (11.2 inches) maximum.
Overlaid display backs showing horizontal VESA spacings of 200, 300, 350, and 400 mm.

Fasten the VESA Mount to your display

Place your display face-down on a soft surface.

Display resting face-down on a protective sheet.

Place the VESA Mount directly against your display.

VESA plate lying against the lower back of the display, with its flange at the bottom edge.
Side cross-section of the display and plate, enlarged to show the flange facing away from the display.

Position the VESA Mount so its flange is nearly flush with the lower edge of your display.

VESA plate shown in several vertical positions, with an arrow indicating adjustment along the display back.

Align the lower two mounting holes of your display with the holes in the VESA Mount.

Two display mounting holes circled through the rows of holes in the VESA plate.

Attach the mounting rails of your wall mount (not included) to your display.

For the upper two mounting positions, place the supplied spacers between each mounting rail and the back of the display.

Two wall-mount rails above the display, with four bolts and two spacers aligned with their mounting positions.
Wall-mount rails fastened over the VESA plate at the lower mounting positions, with upper fasteners and spacers visible.

Mount the display on the wall.

Rear perspective view of the display with the wall-mount bracket and VESA plate installed.
Straight rear view of the display with the wall-mount rails and lower VESA plate.

Route the cables that will connect to the video bar through the center notch in the VESA bracket.

Two cables routed down behind the display and through the plate’s center notch, with excess length looped behind the display.

Attach your video bar to the Video Bar Mount

Check the video bar mounting pattern. The widest hole pattern supported is 218mm (8.6") × 62.5mm (2.5").

Slotted Video Bar Mount diagram dimensioned for a maximum hole pattern of 218 mm by 62.5 mm.

Attach your video bar's wall mount (not included) to the Video Bar Mount using the thumbnut and thumbscrew fasteners included with the Heckler kit.

Video bar wall bracket aligned against the slotted plate, with thumb fasteners at the attachment points.

Loosen the thumbscrews on the underside of the VESA Mount.

Pass the cables through the cutout in the Video Bar Mount.

Slide the Video Bar Mount onto the VESA Mount.

Slide the Video Bar Mount back until it touches the wall.

Animated side view showing the Video Bar Mount engaging the VESA flange and moving back toward the wall, with cables passing through the opening.

Tighten the thumbscrews on the VESA Mount to secure the position.

Underside of the joined mounts, with two thumbscrews highlighted and cable ends passing through the center opening.

Connect the cables to the video bar.

Video bar tilted outward below the display, with cables connected at its rear.

Attach the video bar to the wall mount.

Video bar attached beneath the display.

Common installation examples.

Wall Mount for Rally Bar and Rally Bar Mini

Four circled fasteners joining a Rally Bar wall bracket to the slotted Video Bar Mount.
Front view of a larger Rally Bar beneath the display.
Front view of a smaller Rally Bar Mini beneath the display.

Wall Mount for Rally Bar Huddle

Rally Bar Huddle wall bracket on the slotted plate, with its fastener locations circled.
Rally Bar Huddle installed below the display.

Wall Mount for Neat Bar and Neat Bar Pro

Neat wall bracket centered on the slotted plate, with two fastener locations circled.
Neat video bar beneath the display, with a transparent view of its mounting bracket.