H604 · iPad 10.2-inch · 7th Generation

Side Mount for iPad 10.2-inch 7th Generation

Installation instructions, hardware and source diagrams for H604 Side Mount for iPad 10.2-inch 7th Generation.

This guide is also available as a printable PDF.

Letter PDF A4 PDF

Applies to

Applies to H604 · iPad 10.2-inch · 7th Generation, as identified in the linked source PDF.

In the box and tools needed

1 × M3 hex key (F529)
2 × thread-forming mounting screw (F486)

Keep your assembly tool in a safe place. To purchase a replacement, please contact service@hecklerdesign.com.

You will also need:

Phillips head screwdriver
Drill
Marker

H604 Side Mount for iPad 10.2-inch 7th Generation: In the box and tools needed. Original installation illustration with its hardware labels and orientation details.

Tools: installation dimensions and template

Important Note: A minimum 1.5 inch (38mm) set back from mullion face to the glass is required for an optimal installation in which the front face of the enclosure is flush with the front face of the mullion.

ADA Compliance Guideline (original source): For ADA compliance, the center of the Ethernet cable hole should be no higher than 45 inches above the ground.

Creating The Ethernet Cable Hole: If your Ethernet cable has an RJ45 connector installed, drill a 5/8 inch hole in the position shown. If you will install an RJ45 connector after the Ethernet cable is drawn through the mullion, a smaller hole can be created.

Selecting Your Mounting Screw Positions: To accommodate various mullion styles, multiple screw hole positions are available. Please select the mounting positions that work best for your mullion.

You may use any screw you see fit for mounting the product to the mullion. If you choose to use the self-tapping mounting screws provided, we recommend drilling a pilot hole with a #17 drill bit or a 5/32-inch drill bit.

Original template labels, preserved for review. Drawing is not to scale.
Source drawing label	Original value
Offset near the top of the screen	1 inch (55 mm) — conflicting units; needs correction
Adjacent offset	0.75 inch (19 mm)
Vertical dimensions shown	48 inch; 45 inch
Offset shown twice	1.25 inch (31.8 mm)
Additional dimensions	2.5 inch (63.5 mm); 7.91 inch (201 mm)

The source illustration compares the mullion door frame and glass before and after installation, with the top of the screen and ground marked.

H604 Side Mount for iPad 10.2-inch 7th Generation: Tools: installation dimensions and template. Original installation illustration with its hardware labels and orientation details.

Disassemble Side Mount

Remove mounting bracket from front bezel

2 Remove Mounting Bracket From

Front Bezel

Mark hole positions

3 Mark Hole Positions

Please select the mounting positions that work best for your mullion.

H604 Side Mount for iPad 10.2-inch 7th Generation: Mark hole positions. Original installation illustration with its hardware labels and orientation details.

Drill mounting holes

4 Drill Mounting Holes

You may use any screw you see fit for mounting the product to the mullion.

If you choose to use the self-tapping mounting screws provided, we recommend drilling a pilot hole with a #17 drill bit or a 5/32-inch drill bit.

H604 Side Mount for iPad 10.2-inch 7th Generation: Drill mounting holes. Original installation illustration with its hardware labels and orientation details.

Form mounting-hole threads

5 Form Mounting Hole Threads

F486

The mounting screws provided are thread-forming screws.

H604 Side Mount for iPad 10.2-inch 7th Generation: Form mounting-hole threads. Original installation illustration with its hardware labels and orientation details.

Create the Ethernet cable hole

Ethernet Cable Hole

If your Ethernet cable has an RJ45 connector installed, drill a 5/8 inch hole in the position shown.

If you will install an RJ45 connector after the Ethernet cable is drawn through the mullion, a smaller hole can be created.

H604 Side Mount for iPad 10.2-inch 7th Generation: Create the Ethernet cable hole. Original installation illustration with its hardware labels and orientation details.

Remove mounting screws

6 Remove Mounting Screws

Fasten mounting bracket to the mullion

Fasten Mounting Bracket to mullion

F486

H604 Side Mount for iPad 10.2-inch 7th Generation: Fasten mounting bracket to the mullion. Original installation illustration with its hardware labels and orientation details.

Choose charging and data connections

8 Charging Options

PoE Splitter (Power Only)

PoE Splitter (With wired data connection)

1. Apple Lighting to USB 3 Camera Adapter

2. Apple USB Ethernet Adapter

Battery Bank

H604 Side Mount for iPad 10.2-inch 7th Generation: Choose charging and data connections. Original installation illustration with its hardware labels and orientation details.

Install the tablet

Install Tablet

Install the front bezel

Install Front Bezel

Slide bezel onto the mounting bracket

Slide Front Bezel Onto Mounting Bracket

Tighten assembly screws

F529

Support: source compatibility and original warranty

WindFall ®

SIDE MOUNT

Room Scheduling Enclosure for iPad 10.2-inch 7th Generation

Assembly & Installation

Compatible with:

Limited Warranty

iPad 10.2-inch 7th Generation

Heckler Design warrants your product to be free from defect in material and workmanship for a period of two years from the original date of purchase. Electronic components are warranted to be free from defect for a period of one year from the original date of purchase. If you discover a defect, please contact service@hecklerdesign.com. Heckler Design will repair, at our discretion, using new or refurbished components. If repair is not possible, Heckler Design will replace the item.

H604