1 x Front Panel 1 x Shelf 1 x Device Panel 2 x Side Cover Enlarge image ↗ Exploded included-parts drawing labeled a–d: front panel, shelf, device panel, and two side covers.
1 x Bottom bracket set 1 x Top bracket set 1 x Hex Key 4 x Quick-release pin 8 x Rack-mounting screw 1 x Velcro Enlarge image ↗ Included hardware labeled e–j: bottom and top bracket sets, hex key, quick-release pins, rack-mounting screws, and coiled hook-and-loop material.
Tape measure Level Masking tape Based on your desired camera lens height, and the distance between the lens and the shelf, determine the desired mounting height of the shelf.
To help ensure your front panel obscures visibility of your wall outlets, we recommend you install your shelf 36 to 40 inches above your floor.
Use masking tape to mark the shelf height.
Enlarge image ↗ Shelf height marked horizontally across the AV Wall uprights beneath the outlined camera.
Hook the left bracket and right bracket into the AV Wall structure as shown.
Enlarge image ↗ Four close-ups showing the left top bracket hooked into the upright and lowered into position.
Enlarge image ↗ Rear close-ups showing the top bracket hooks engaging the upright openings.
Enlarge image ↗ Two installed top brackets at the marked height, with quick-release pin locations indicated.
Verify the left and right brackets are at the same height.
Enlarge image ↗ Dashed horizontal reference connecting the top brackets to show equal height.
Loosen the mounting screw.
Enlarge image ↗ Hex key at the left top bracket mounting screw, with a curved loosening arrow.
Repeat on the right bracket.
Enlarge image ↗ Hex key at the right top bracket mounting screw.
Lower the shelf onto the top brackets as shown.
Enlarge image ↗ Shelf aligned above the two top brackets.
Enlarge image ↗ Shelf resting on the brackets, with its two mounting positions circled.
Enlarge image ↗ Four close-ups showing shelf keyholes engaging the screw heads and the screws tightened with a hex key.
Tighten the mounting screws.
Enlarge image ↗ Shelf secured to the two top brackets.
Enlarge image ↗ Lower bracket positions circled on the AV Wall uprights beneath the shelf.
Using masking tape, mark a location 20 3/8 inches below the bottom edge of the shelf.
Enlarge image ↗ Bottom bracket height shown as 20 3/8 inches below the shelf’s bottom edge.
Enlarge image ↗ Close-up of the bottom bracket position and the 20 3/8-inch reference from the shelf.
Enlarge image ↗ Four close-ups showing a bottom bracket hooked into the upright and lowered into position.
Enlarge image ↗ Rear close-ups showing bottom bracket hooks engaging the upright openings.
Enlarge image ↗ Installed bottom brackets with quick-release pins shown at their locking positions.
Verify the left and right brackets are at the same height.
Enlarge image ↗ Dashed horizontal reference connecting the bottom brackets to show equal height.
Devices and wiring can be strapped to the device panel before or after the device panel is installed to Heckler AV Wall.
Enlarge image ↗ Devices and cables strapped to the perforated device panel.
Enlarge image ↗ Two device-panel mounting screws beneath the shelf circled.
Slightly loosen the two Device Panel mounting screws.
Enlarge image ↗ Hex key loosening a device-panel mounting screw.
Hang the Device Panel on the mounting screws as shown.
Tighten the mounting screws.
Enlarge image ↗ Loaded device panel hanging beneath the shelf on its mounting screws.
Enlarge image ↗ Four close-ups showing device-panel keyholes engaging the screws and the screws tightened with a hex key.
Remove the side panel thumbscrews.
Enlarge image ↗ Close-ups of the side-panel thumbscrews removed from the upper and lower brackets.
Fasten the component in place using the rack-mounting screws provided or your favorite 10-32 rack-mounting screws.
Enlarge image ↗ Optional rack-mount component positioned vertically between the left brackets with its mounting screws.
Install the side panel as shown with the provided thumbscrews.
Enlarge image ↗ Side cover fastened to the upper and lower brackets with thumbscrews.
Rest your camera on the shelf using your camera’s table stand.
If your camera’s table stand features a 1/4 inch diameter mounting hole, you can fasten your camera to the shelf. Hardware not included.
Enlarge image ↗ Video bar resting on its table stand on the shelf.
Enlarge image ↗ Camera-stand mounting hole shown from beneath the shelf.
Carefully lower the ball joints on the rear of the panel into the bottom brackets as shown.
Enlarge image ↗ Front panel tilted and lowered toward the two bottom brackets.
Enlarge image ↗ Close-up showing a rear ball joint aligned with the bottom bracket opening.
Enlarge image ↗ Ball joint seated in the bottom bracket.
Push the panel toward the shelf until the magnets engage. The upper edge of your panel should be positioned directly below the front edge of the shelf.
Enlarge image ↗ Front panel rotating upward toward the magnetic attachment below the shelf.
Enlarge image ↗ Completed AV Wall with display, camera on the shelf, and front panel beneath it.
