H892

Heckler AV Credenza Mini

Mount AV Credenza Mini, arrange devices and cables, and install the camera bracket, cable chase, and front panel.

This guide is also available as a printable PDF.

Letter PDF A4 PDF

In the box

1 x main body (R800)
1 x front panel (R501)
1 x mounting bracket for Rally Bar, Rally Bar Mini, and Rally Bar Huddle (R740)
1 x cable chase (R550)
1 x wall-mounting template (K394)
2 x mounting screw for camera brackets (F036)
2 x mounting screw for Rally Bar & Rally Bar Mini (F038)
1 x hex key for installing camera brackets (F776)
1 x set screw for mounting PTZ cameras (F040)
1 x wingnut for mounting PTZ cameras (F041)
1 x spacer for mounting PTZ cameras (F042)
4 x drywall-mounting screw (F039)
4 x drywall-mounting washer (F035)
4 x drywall-mounting spacer (F034)
4 x drywall-mounting wall anchor (F037)
5-foot roll of hook & loop strap (F947)
5 x strapping buckle (F751)
2 x key (F033)

Included credenza components labeled A–R: body, front panel, camera bracket, cable chase, template, mounting hardware, tool, straps, buckles, and keys.

Tools needed

Power drill
1/2-inch drill bit
Phillips screwdriver
Masking tape
Level
Tape measure
Stud finder

Install wall anchors

Tape the wall-mounting template (E) to the wall. Use a level.

Mark the locations of wall studs on the mounting template.

Mark the hole locations on the wall. Select one hole location for each corner of the credenza.

Wall template positioned above an outlet, with mounting-hole choices marked at each corner and the recommended height dimensions shown.

Remove the template from the wall.

Drill holes in the drywall. Use a 1/2-inch diameter drill bit.

Install the wall anchors(O).

How to install SNAPTOGGLE wall anchors

1. Hold metal channel flat alongside plastic straps & slide channel through the hole. Minimum clearance behind wall: only 1-7/8” 2. Hold ends of straps together between thumb & forefinger and pull toward you until channel rests behind wall. Ratchet cap along straps with other hand until flange of cap is flush with wall. 3. Place thumb between straps at wall. Push thumb side to side, snapping off straps level with flange of cap. 4. Place item over flange. Insert bolt and tighten until snug against item, then stop. Use machine screw or bolt to match thread in metal channel.

Pass the wall mounting screws(L) and washers(M) through the white nylon spacers(N), then fasten loosely into the wall in the upper left and upper right mounting positions.

Two upper wall screws, washers, and spacers aligned with their anchor positions.

Exploded and assembled views of a wall screw, washer, spacer, and anchor, leaving the screw projecting from the wall.

Mount devices and cabling

Cut the provided hook-and-loop straps (P) to the lengths needed for securing components and managing cables.

Use buckles(Q) to firmly strap components.

Strap components to the grid of large rectangular holes on the rear and bottom surfaces of the credenza body.

Devices strapped through the rectangular openings on the rear and bottom of the credenza body.

Device mounting plate aligned with four small mounting holes between the credenza’s rectangular openings.

Install credenza body

Hang the credenza on the top two anchor screws.

Animation showing the credenza body engaging the two upper wall screws through its keyhole slots.

Close-up of an upper wall screw seated in the narrow part of a credenza keyhole slot.

Fasten mounting screws(L) and washers(M) through the lower corners of the credenza body. Position a white nylon spacer(N) between the body and the wall in each lower corner.

The two lower mounting positions circled on the installed credenza body.

Exploded and assembled views of the lower wall screw and washer passing through the credenza, with a spacer behind it.

Install camera bracket for Logitech Rally Bar & Rally Bar Mini

Fasten the bracket(C) to Rally Bar with the 1/4-20 screws(G) and key(H) provided.

Camera bracket aligned with the underside of a Rally Bar, with two mounting screws and a hex key.

Fasten mounting screws(F) to the bracket with key(H) provided.

Two mounting screws aligned with the lower holes in the bracket attached to the Rally Bar.

Slide the bracket’s mounting screws into the horizontal keyhole slots on the back wall of the credenza.

Tighten the screws with the provided hex key(H).

Animation showing the Rally Bar bracket lowered to the credenza and its screws engaging the horizontal keyhole slots.

Install camera bracket for PTZ cameras

Fasten the provided 1/4-20 set screw(I) and black spacer(K) into your camera.

Spacer and threaded stud aligned beneath a PTZ camera.

Place the camera on the top surface. Use the black spacer provided to lift the camera from the top surface a small distance. Fasten the camera to the credenza body with the provided wing nut(J).

PTZ camera positioned above the credenza top, with its mounting stud and wingnut passing through the top slot.

Install the cable chase

Remove the thumbscrews from the cable chase(D).

Cable chase with two thumbscrews separated from its lower end.

Organize cables inside the cable chase.

Slide the cable chase down along the rear surface of the Credenza Mini body.

Fasten the two thumbscrews from the front.

Cable chase aligned above the back of the credenza, with a downward arrow indicating placement.

Close-up of two thumbscrews aligned through the credenza into the cable chase.

Fully tighten all four wall mount screws

All four wall-mount screw positions circled on the credenza body.

Install front panel

Lower the front panel onto the body. Rest the four posts on the panel onto the four hooks on the main body.

Animation showing the front panel moving between the open and seated positions on the credenza.

Transparent front-panel view showing its posts aligned with the hooks on the credenza body.

Use the provided keys(R) to turn the cam lock on the underside of the credenza body.

Completed wall-mounted display, Rally Bar, and credenza with its front panel fitted.