Important: Read Before Assembly
Thank you for choosing the Heckler Collaboration Stand MKII. To ensure safe and proper assembly, operation, and maintenance of this product, it is essential to thoroughly read and understand this user guide before beginning any assembly.
Failure to follow the instructions and safety guidelines provided in this manual may result in serious personal injury, equipment damage, or voided warranties.
Assembly Requirements: This product requires multiple people to assemble and safely mount the display. Attempting to assemble or mount the display alone could result in injury or damage to the equipment.Weight and Stability: Ensure that the stand is placed on a stable, level surface during assembly and when in use. Uneven or unstable surfaces may cause the stand to tip over, leading to potential injury or damage.Display Mounting: Mounting a display on this stand requires careful attention to weight limits and proper alignment. Exceeding weight limits or incorrect mounting can cause the display to fall, resulting in injury or damage.Secure All Components: Ensure all bolts, screws, and other fasteners are securely tightened and engaged as per the instructions. Loose or improperly engaged components may cause the stand or display to become unstable.Electrical Safety: If your display or any attached components require electrical connections, ensure that all wiring is correctly installed and free of damage. Avoid routing cables where they could be pinched or damaged during assembly or operation.Routine Inspection: Regularly inspect the stand and mounted display for any signs of wear, damage, or loose components. Address any issues immediately to maintain safety and functionality.Heckler Design is not liable for any injuries, damages, or losses resulting from improper assembly, use, or maintenance of this product. By assembling and using this product, you agree to follow all safety guidelines and instructions provided in this user guide.
1 x Beam (R1115) 4 x Leg (R1116) 2 x Column (R1117) 4 x Caster (F189) 4 x M8 display anchor (P123-2) 4 x M8 set screw (F519) 4 x M6 display anchor (P124-2) 4 x M6 set screw (F589) 1 x Cord wrap right (P317) 1 x Cord wrap left (P316) 6 x Cable manager (P275) 1 x Hex key (F674) 2 x Beam cap (P291) Enlarge image ↗ Beam, leg, and display column labeled a, b, and c.
Enlarge image ↗ Caster, display anchors and set screws, cord-wrap hooks, cable manager, hex key, and beam cap labeled d through m.
Engage the caster brake.
The casters have a total lock feature, locking the wheels from spinning as well as the swivel axis from swiveling.
Enlarge image ↗ A caster's brake pedal highlighted with a downward arrow.
Thread the caster into the leg socket.
Enlarge image ↗ A threaded caster stem aligned with the leg socket, with rotation arrows in an enlarged detail.
Thread the caster all the way into the leg insert. The hex feature of the caster should be fully seated inside the leg socket.
Enlarge image ↗ Close-up of the caster stem threading into the leg insert.
Enlarge image ↗ The caster fully threaded into the leg, with its hex feature seated at the socket.
If the leg becomes misaligned during your installation attempt, remove the leg from the socket and try again. Attempting to pry or force a misaligned leg into position may cause damage to the stand.
Align the beam cap with the cutout on the end of the beam and install the beam cap on both ends of the beam.
Enlarge image ↗ A beam cap's alignment tab directed toward the matching cutout at the beam end.
Enlarge image ↗ The beam cap installed flush at the beam end.
Lay the beam on the ground and install the first leg. Use the supplied hex key to back out each set screw to enable the leg to slide into the socket without striking the tip of the set screws. Do not fully back out the set screws. They must remain engaged with the beam.
Each leg socket ships with two set screws pre-installed. Check to ensure two set screws are present at each leg socket location. If any set screws are missing, check your packaging and contact Heckler customer service for replacement parts.
Enlarge image ↗ A hex key backing out a leg-socket set screw, with the second set screw beside it.
Orient the leg so that the surface with the two holes aligns with the two set screws, then insert the leg into the socket.
Enlarge image ↗ The leg's two conical holes aligned with the two beam set screws.
Depress the silver safety push pin on the side of the leg, then push the leg fully into the socket.
Enlarge image ↗ The leg entering its socket as its side safety push pin is pressed inward.
When correctly inserted, the safety push pin will click inside of the round beam tube and the two tabs on the end of the leg will be flush with the outside surface of the beam.
Enlarge image ↗ The leg's two end tabs and safety push pin highlighted inside the beam.
Tighten the two set screws.
Tighten the screws firmly, but do not overtighten. The set screws should rest near-flush to the beam surface. The set screws should not sink into the beam beyond flush.
As the set screws fasten into place, the conical tips of the set screws will align with the conical holes in the leg. You’ll feel the leg align into its final position.
Enlarge image ↗ A hex key tightening the two set screws against the seated leg.
Enlarge image ↗ The first leg attached to the beam while the assembly rests on the floor.
Repeat the process with the remaining three legs.
Enlarge image ↗ The remaining legs installed while the base lies on its side.
Raise the completed stand base upright.
Enlarge image ↗ The assembled stand base upright on four casters.
Engage the brake on all four casters.
Enlarge image ↗ Close-up of a caster with its brake pedal highlighted.
Identify your display’s horizontal VESA pattern and choose the corresponding column inserts on the beam.
Heckler Collaboration Stand MKII is compatible with most displays with VESA 200, VESA 400, VESA 600, and VESA 800 mounting patterns.
Enlarge image ↗ Beam sockets labeled for 200, 400, 600, and 800 mm horizontal VESA spacing.
Displays with VESA 300, VESA 500, and VESA 700 horizontal mounting patterns are also compatible. To mount VESA 300, VESA 500, and VESA 700 displays, move one column away from the center of the beam. The resulting install will off-center the display to the stand body by 50 mm.
Enlarge image ↗ Beam sockets labeled for 300, 500, and 700 mm horizontal VESA spacing.
The set screws for the columns are pre-installed at the 400 mm locations. Each column socket ships with two set screws pre-installed. Check to ensure two set screws are present at both column-socket locations. If any set screws are missing, check your packaging and contact Heckler customer service for replacement parts.
Enlarge image ↗ The 400 mm column-socket positions marked, with two preinstalled set screws shown in an inset.
If your display has a horizontal 400 mm VESA pattern, use the supplied hex key to back out each set screw to enable the column to slide into the socket without striking the tip of the set screws.
Enlarge image ↗ A hex key backing out a set screw at a column socket.
If your display has a horizontal VESA pattern other than 400 mm, remove the cable manager and relocate the set screws to the corresponding locations on the beam. Make sure the column can slide into the socket without striking the tips of the set screws.
Enlarge image ↗ A cable manager lifting out of an unused beam socket.
Enlarge image ↗ Set screws moving from one column-socket position to another, indicated by a dashed arrow.
Align and insert the end of the column into the socket on the beam.
Hold the column vertically throughout this process to ensure proper socket alignment. If the column becomes misaligned during your installation attempt, remove the column from the socket and try again. Attempting to pry or force a misaligned column into position may cause damage to the stand.
Enlarge image ↗ Side views showing a display column held vertically above a beam socket and then seated.
Enlarge image ↗ A display column positioned above its chosen beam socket.
Enlarge image ↗ The end of the column aligned with the beam socket and set-screw positions.
Depress the silver safety push pin on the side of the column, then push the column fully into the socket.
Enlarge image ↗ The column's safety push pin pressed inward as the column lowers into the socket.
When correctly inserted, the safety push pin will click inside of the round beam tube and the two tabs on the end of the column will be flush with the outside surface of the beam.
Enlarge image ↗ The column's two end tabs seated through the beam, highlighted through a transparent view.
Tighten the two set screws.
Tighten the screws firmly, but do not overtighten. The set screws should rest near-flush to the beam surface. The set screws should not sink into the beam beyond flush.
As the set screws fasten into place, the conical tips of the set screws will align with the conical holes in the column. You’ll feel the column align into its final position.
Enlarge image ↗ A hex key tightening the set screws against the installed column.
Enlarge image ↗ One display column installed on the base.
Repeat this process to install the second column.
Enlarge image ↗ Both display columns installed on the base.
This stand is designed to safely mount displays with screen sizes 50 to 75 inches, with VESA 200 to VESA 800 horizontal mounting patterns, weighing up to 220 pounds.
Determine if your display has M6 or M8 size mounting holes.
Fasten the supplied display-mounting screws into the four VESA mounting positions on your display.
In most cases, no tools are needed for this step. Fasten by hand. If you used a tool (not included) to fasten the set screws, do not overtighten.
Enlarge image ↗ Four set screws at the display's rear VESA mounting holes, with an enlarged screw detail.
Fully fasten the display anchors to the set screws. Do not overtighten.
Each display anchor features an embedded steel nut. Ensure the set screw fully threads through this nut.
Enlarge image ↗ Four display anchors fitted over the set screws, with enlarged threaded-anchor details.
Choose the mounting position on the columns based on the preferred display mounting height.
Enlarge image ↗ The display's four anchors aligned with the column keyholes.
Bring the display close to the columns, fully insert all four display anchors into the four mounting keyholes on the columns, then lower the anchors onto the keyholes. This will hold the display to the stand.
Enlarge image ↗ The display lowered onto the columns, with enlarged views of an anchor entering and seating in a keyhole.
To create a safe assembly, the display must be affixed in place. To do so, insert a cable manager through the rear holes on each column corresponding to each display anchor.
Enlarge image ↗ Cable managers entering the rear column holes at the display-anchor locations, shown before and after seating.
Install cord wrap hooks into the unused sockets on the beam.
Enlarge image ↗ A cord-wrap hook aligned with an unused beam socket beside the installed opposite hook.
Enlarge image ↗ A cable routed from the rear display down a column and along the beam.
Enlarge image ↗ Close-up of cables passing through a column cable manager and around the beam cord-wrap hooks.
With the display removed, first back out the set screws to disassemble the columns and legs from the beam.
Enlarge image ↗ A hex key backing out the leg-socket set screws for disassembly.
Push the included hex key through the hexagonal cutout on each leg or column to release the safety pin, then pull the part out of the beam.
Enlarge image ↗ The included hex key pressing the safety pin through the side cutout while the leg begins to slide out.
Enlarge image ↗ The leg withdrawn from the beam socket after its safety pin is released.
Enlarge image ↗ Front view of the completed Collaboration Stand MKII with a display.
